Body: Full Metal
Weight: 715 g
Height: 139 mm
Length: 216 mm
Caliber: 6 mm
|
Full scale: 1:1 Body: Full Metal Weight: 715 g Height: 139 mm Length: 216 mm Caliber: 6 mm |
|
 |
|
To refill the gas with the gas container in vertical position |
 |
| back to top |
|
Loading BB Bullet Load BB bullet in the magazine, 6 mm (24 rounds only) Please do not use the B bullets that are over 6mm, rough on surface or have been used |
 |
| back to top |
|
Load and release the magazine While loading the magazine, push it inward to the bottom till a "tick" sound is heard. Press the magazine release catch, the magazine will fall off from the stock. Attention: use hand to receive the magazine to prevent it from falling down to the ground. |
 |
| back to top |
|
First load of bullet for firing Pull the slide backward to a specific position, then release and let the slide moving forward to load the bullet in the firing chamber, and retain the hammer at the rear position, ready for firing. |
 |
| back to top |
 |
| back to top |
|
When the slide is pulled back and released forward, the bullet is load-ed in the firing chamber, press
the trigger to fire the loaded bullet. Attention: The maximum containment for a magazine is 25 rounds. After the last BB bullet is fired, the slide will be retained in the back position, it means an empty magazine condition. If you want to resume the firing, insert a new fully loaded magazine, press the slide stop to release the slide and to reload the bullet. |
 |
| back to top |
| After a long and continued firing practice, the low temperature of the magazine will cause a reduced gas pressure as well as the low velocity of bullet. It is a normal condition, not a trouble. Never practice the reverse firing for this action renders the gas hardness to volatilize and to produce the atomized gas of ejection which leads the damaged to the parts. |
 |
| back to top |
| After the firing practice, take off the magazine
from the stock, push down the slide stop to hold the slide in place and
press the trigger to release the hammer.
Attention: Take out any bullet that is inside. |
 |
| back to top |
 |
| back to top |
 |
| back to top |
 |
| back to top |
 |
| back to top |
| Condition | Causes | Correction |
| No action | Safety is locked | Release the safety |
| Too much gas |
Press the refill inlet or the drain valve to breed an adequate amount
of gas. Caution: Never aim the discharged gas to a fire, animal, or person |
|
| Insufficient gas |
Insufficient gas filled or at a very low temperature. Solution: Inject an adequate amount of gas into the gun |
|
| Unknown reason | Please contact our distributor. | |
| No load of bullet | Deformed BB bullet | Use the standard BB bullet only |
| The bore is clogged with extraneous material | Remove the extraneous material from the bore | |
| The slide fails to return to the position | An extraneous material jams at the front end of the barrel | Remove the extraneous material |
| The motion of the slide is not smooth while firing BB bullet | The ambient temperature is too low (in winter) | Place the magazine indoor to recover the temperature. It is recommended to
prepare two magazines. Refill the gas |
| Insufficient gas in the magazine (a long and continued firing causes quick cooling and frozen) | ||
| Low gas pressure in the magazine | ||
| The trigger mechanism is out of work. | Please contact our distributor | |
| The air-tight rubber seal is worn out or damaged | ||
| Poor lubrication | Please carry out the periodic lubrication accordingly | |
| Short projectile | The rubber seal is damaged | Please contact our distributor |
| The spring fatigue | ||
| The gas discharging mechanism is broken | ||
| back to top | ||
|
Be sure to wear shooting glasses or Goggle when shooting. Put the gun beyond the reach of kids. DO NOT peep at the muzzle. DO NOT aim at people even if it is unloaded. DO NOT touch the trigger until the moment of shooting. After making sure that there is nobody nearby. Avoid a rough operation. When the gun is not in use, remove the magazine and unload BB pellets. |
| back to top |